Part Number To Suit Hole Ø Ød1 Min. Ød1 Max. Ød1 Min. Ød1 Max. L Cost Quantity Order SCP8.0-32 8 7.30 7.50 2.00 4.00 32 £0.31 SCP8.0-36 8 7.30 7.50 2.00 4.00 36 £0.33 SCP8.0-40 8 7.30 7.50 2.00 4.00 40 £0.36 SCP8.0-45 8 7.30 7.50 2.00 4.00 45 £0.43 SCP8.0-50 8 7.30 7.50 2.00 4.00 50 £0.46 SCP8.0-56 8 7.30 7.50 2.00 4.00 56 £0.49 SCP8.0-63 8 7.30 7.50 2.00 4.00 63 £0.51 SCP8.0-71 8 7.30 7.50 2.00 4.00 71 £0.54 SCP8.0-80 8 7.30 7.50 2.00 4.00 80 £0.57 SCP8.0-90 8 7.30 7.50 2.00 4.00 90 £0.59 SCP8.0-100 8 7.30 7.50 2.00 4.00 100 £0.64 SCP8.0-112 8 7.30 7.50 2.00 4.00 112 £0.71 SCP8.0-125 8 7.30 7.50 2.00 4.00 125 £0.76 SCP8.0-140 8 7.30 7.50 2.00 4.00 140 £0.80 SCP8.0-160 8 7.30 7.50 2.00 4.00 160 £0.89 SCP10.0-32 10 9.30 9.50 3.20 6.30 32 £0.44 SCP10.0-36 10 9.30 9.50 3.20 6.30 36 £0.48 SCP10.0-40 10 9.30 9.50 3.20 6.30 40 £0.51 SCP10.0-45 10 9.30 9.50 3.20 6.30 45 £0.56 SCP10.0-50 10 9.30 9.50 3.20 6.30 50 £0.61 SCP10.0-56 10 9.30 9.50 3.20 6.30 56 £0.66

Part Number To Suit Hole Ø Ød1 Min. Ød1 Max. Ød1 Min. Ød1 Max. L Cost Quantity Order SCP10.0-63 10 9.30 9.50 3.20 6.30 63 £0.69 SCP10.0-71 10 9.30 9.50 3.20 6.30 71 £0.84 SCP10.0-80 10 9.30 9.50 3.20 6.30 80 £0.94 SCP10.0-90 10 9.30 9.50 3.20 6.30 90 £0.95 SCP10.0-100 10 9.30 9.50 3.20 6.30 100 £1.02 SCP10.0-112 10 9.30 9.50 3.20 6.30 112 £1.15 SCP10.0-125 10 9.30 9.50 3.20 6.30 125 £1.24 SCP10.0-140 10 9.30 9.50 3.20 6.30 140 £1.35 SCP10.0-160 10 9.30 9.50 3.20 6.30 160 £1.40 SCP12.0-45 12 12.10 12.40 3.20 6.30 45 £0.65 SCP12.0-50 12 12.10 12.40 3.20 6.30 50 £0.73 SCP12.0-56 12 12.10 12.40 3.20 6.30 56 £0.81 SCP12.0-63 12 12.10 12.40 3.20 6.30 63 £0.94 SCP12.0-71 12 12.10 12.40 3.20 6.30 71 £1.04 SCP12.0-80 12 12.10 12.40 3.20 6.30 80 £1.18 SCP12.0-90 12 12.10 12.40 3.20 6.30 90 £1.29 SCP12.0-100 12 12.10 12.40 3.20 6.30 100 £1.48 SCP12.0-112 12 12.10 12.40 3.20 6.30 112 £1.59 SCP12.0-125 12 12.10 12.40 3.20 6.30 125 £1.77 SCP12.0-140 12 12.10 12.40 3.20 6.30 140 £1.98 SCP12.0-160 12 12.10 12.40 3.20 6.30 160 £2.02

Material
Low Carbon Steel

Other Info.
Cotter pins are made to DIN 94 and are also equal to ISO 1234 and BS 1574.
Steel Pins can be zinc plated or phosphate coated, but since such finishes cannot be applied to the inside faces of the pin, only stainless can be recommended where full corrosion resistance is needed.

Downloads
PDF Documents : Catalogue Pages

Steel: Ø1.0 - Ø2.0 | Ø2.5 - Ø4.0 | Ø5.0 - Ø6.3 | Ø8.0 - Ø12.0
Stainless: Ø1.0 - Ø2.0 | Ø2.5 - Ø4.0 | Ø5.0 - Ø6.3