Ondrives: Mechanical - Dowel & Spring Pins - PP - Plain Jig Bushes - Long

PP : Long Plain Jig Bushes

Mechanical » Dowel & Spring Pins »
PP Type : Plain Jig Bushes - Long Series

Headless Type Press Fit. ISO 4247 / BS 1098 Pt. 2 1977 / DIN 179A

Long Series

Discounts

1+ 0%

10+ 5%

25+ 10%

50+ 15%

100+ 20%

200+ 25%

500+ 30%

1000+ 40%

2000+ 45%

Part Number	C	ØB^h16	ØA^F7		Cost	Quantity	Order
Part Number	C	ØB^h16	From	Up to	Cost	Quantity	Order
PP3C	9	3	-	1.0	£20.48
PP4C	9	4	1.05	1.8	£17.18
PP5C	9	5	1.85	2.6	£12.28
PP6E	12	6	2.65	3.3	£9.15
PP7E	12	7	3.40	4.0	£8.49
PP8E	12	8	4.10	5.0	£9.15
PP10F	16	10	5.10	6.0	£10.03
PP12F	16	12	6.10	8.0	£10.03
PP15H	20	15	8.10	10.0	£10.87
PP18H	20	18	10.10	12.0	£11.85
PP22K	28	22	12.10	15.0	£14.11
PP26K	28	26	15.25	18.0	£15.98
PP30N	36	30	18.25	22.0	£18.98

Part Number	C	ØB^h16	ØA^F7		Cost	Quantity	Order
Part Number	C	ØB^h16	From	Up to	Cost	Quantity	Order
PP35N	36	35	22.25	26.0	£21.78
PP42R	45	42	26.25	30.0	£24.03
PP48R	45	48	30.25	35.0	£29.85
PP55S	56	55	35.50	42.0	£36.61
PP62S	56	62	42.50	48.0	£37.45
PP70S	56	70	48.50	55.0	£POA
PP78T	67	78	56.00	63.0	£POA
PP85T	67	85	64.00	70.0	£POA
PP95W	78	95	71.00	78.0	£POA
PP105W	78	105	79.00	85.0	£POA
PP115X	89	115	86.00	95.0	£POA
PP125X	89	125	96.00	105.0	£POA

Minimum order value of £50 applies.

Material
535A99 (100Cr6) Through hardened Steel 62-64Rc.

Ordering Example =	PP4A	1.05
		Bore size required for order and delivery

Standard Increment Bore Sizes
From 1.0mm to 3mm in steps of 0.05mm.
From 3.0mm to 14mm in steps of 0.10mm.
From 14.0mm to 33mm in steps of 0.25mm (and including all 0.25mm and 0.75mm sizes).
From 33.0mm to 51mm in steps of 0.50mm.
From 51.0mm to 100mm in steps of 1.00mm.

Nitrided bushes for longer life giving a hardness of 67-69 Rockwell C are available at extra cost.

Nominal Sizes		F7 Hole		n6 Shaft
Over	Up to	High+	Low+	High+	Low+
-	3	16	6	10	4
3	6	22	10	16	8
6	10	28	13	19	10
10	18	34	16	23	12
18	30	41	20	28	15
30	50	50	25	33	17
50	80	60	30	39	20
80	120	71	36	45	23

Also Available
(a) Fixed & Slip Renewable: These two features are incorporated on one bush, which is used in conjunction with liner bushes, and is held in place by a lock screw, tenon or stop pin.
The bush is a slide fit in its corresponding liner.
The removable fixed feature of the bush is normally used on high production work, when the bush can be easily and quickly replaced with a minimum loss of production.
The removable slip feature of the bush is used when more than one operation is carried out, when the bush is instantly removable after each operation.
(b) Headless Liner Type: This range is for use in conjunction with Renewable Fixed and Slip type bushes.
(c) Headed Liner Type: As above but headed. The shallow head can be left standing proud or countersunk flush.

Imperial sizes for all types available.

Downloads
PDF Documents : Catalogue Pages