Ondrives: Mechanical - Dowel & Spring Pins - PP - Plain Jig Bushes - Extra Long

PP : X-Long Plain Jig Bushes

Mechanical » Dowel & Spring Pins »
PP Type : Plain Jig Bushes - Extra Long Series

Headless Type Press Fit. ISO 4247 / BS 1098 Pt. 2 1977 / DIN 179A

Extra Long Series

Discounts

1+ 0%

10+ 5%

25+ 10%

50+ 15%

100+ 20%

200+ 25%

500+ 30%

1000+ 40%

2000+ 45%

Part Number	C	ØB^h16	ØA^F7		Cost	Quantity	Order
Part Number	C	ØB^h16	From	Up to	Cost	Quantity	Order
PP6F	16	6	2.65	3.3	£10.32
PP7F	16	7	3.40	4.0	£10.47
PP8F	16	8	4.10	5.0	£10.87
PP10H	20	10	5.10	6.0	£11.67
PP12H	20	12	6.10	8.0	£11.72
PP15J	25	15	8.10	10.0	£12.17
PP18J	25	18	10.10	12.0	£13.11
PP22N	36	22	12.10	15.0	£14.66
PP26N	36	26	15.25	18.0	£19.97
PP30R	45	30	18.25	22.0	£25.99
PP35R	45	35	22.25	26.0	£27.38

Part Number	C	ØB^h16	ØA^F7		Cost	Quantity	Order
Part Number	C	ØB^h16	From	Up to	Cost	Quantity	Order
PP42S	56	42	26.25	30.0	£31.58
PP48S	56	48	30.25	35.0	£32.70
PP55T	67	55	35.50	42.0	£44.45
PP62T	67	62	42.50	48.0	£45.30
PP70T	67	70	48.50	55.0	£POA
PP78W	78	78	56.00	63.0	£POA
PP85W	78	85	64.00	70.0	£POA
PP95Y	105	95	71.00	78.0	£POA
PP105Y	105	105	79.00	85.0	£POA
PP115Z	112	115	86.00	95.0	£POA
PP125Z	112	125	96.00	105.0	£POA

Minimum order value of £50 applies.

Material
535A99 (100Cr6) Through hardened Steel 62-64Rc.

Ordering Example =	PP4A	1.05
		Bore size required for order and delivery

Standard Increment Bore Sizes
From 1.0mm to 3mm in steps of 0.05mm.
From 3.0mm to 14mm in steps of 0.10mm.
From 14.0mm to 33mm in steps of 0.25mm (and including all 0.25mm and 0.75mm sizes).
From 33.0mm to 51mm in steps of 0.50mm.
From 51.0mm to 100mm in steps of 1.00mm.

Concentricity is 0.2mm on drilled or ground bores up to 1.4mm
Nitrided bushes for longer life giving a hardness of 67-69 Rockwell C are available at extra cost.

Nominal Sizes		F7 Hole		n6 Shaft
Over	Up to	High+	Low+	High+	Low+
-	3	16	6	10	4
3	6	22	10	16	8
6	10	28	13	19	10
10	18	34	16	23	12
18	30	41	20	28	15
30	50	50	25	33	17
50	80	60	30	39	20
80	120	71	36	45	23

Also Available
(a) Fixed & Slip Renewable: These two features are incorporated on one bush, which is used in conjunction with liner bushes, and is held in place by a lock screw, tenon or stop pin.
The bush is a slide fit in its corresponding liner.
The removable fixed feature of the bush is normally used on high production work, when the bush can be easily and quickly replaced with a minimum loss of production.
The removable slip feature of the bush is used when more than one operation is carried out, when the bush is instantly removable after each operation.
(b) Headless Liner Type: This range is for use in conjunction with Renewable Fixed and Slip type bushes.
(c) Headed Liner Type: As above but headed. The shallow head can be left standing proud or countersunk flush.

Imperial sizes for all types available.

Downloads
PDF Documents : Catalogue Pages