Ondrives: Mechanical - Dowel & Spring Pins - PH - Headed Jig Bushes - Extra Long

PH : X-Long Headed Jig Bushes

Mechanical » Dowel & Spring Pins »
PH Type : Headed Jig Bushes - Extra Long Series

Headless Type Press Fit. ISO 4247 / BS 1098 Pt. 2 1977 / DIN 172A

Extra Long Series

Discounts

1+ 0%

10+ 5%

25+ 10%

50+ 15%

100+ 20%

200+ 25%

500+ 30%

1000+ 40%

2000+ 45%

Part Number	C	ØB^h16	ØD^h13	E	ØA^F7		Cost	Quantity	Order
Part Number	C	ØB^h16	ØD^h13	E	From	Up to	Cost	Quantity	Order
PH6F	16	6	9	2.5	2.65	3.3	£12.55
PH7F	16	7	10	2.5	3.40	4.0	£12.41
PH8F	16	8	11	2.5	4.10	5.0	£13.11
PH10H	20	10	13	3.0	5.10	6.0	£13.97
PH12H	20	12	15	3.0	6.10	8.0	£13.97
PH15J	25	15	18	3.0	8.10	10.0	£14.51
PH18J	25	18	22	4.0	10.10	12.0	£15.63
PH22N	36	22	26	4.0	12.10	15.0	£17.60
PH26N	36	26	30	4.0	15.25	18.0	£23.75
PH30R	45	30	34	5.0	18.25	22.0	£31.87
PH35R	45	35	39	5.0	22.25	26.0	£34.04

Part Number	C	ØB^h16	ØD^h13	E	ØA^F7		Cost	Quantity	Order
Part Number	C	ØB^h16	ØD^h13	E	From	Up to	Cost	Quantity	Order
PH42S	56	42	46	5.0	26.25	30.0	£37.81
PH48S	56	48	52	5.0	30.25	35.0	£43.30
PH55T	67	55	59	5.0	35.50	42.0	£55.25
PH62T	67	62	66	6.0	42.50	48.0	£55.92
PH70T	67	70	74	6.0	48.50	55.0	£POA
PH78W	78	78	82	6.0	56.00	63.0	£POA
PH85W	78	85	90	6.0	64.00	70.0	£POA
PH95Y	105	95	100	6.0	71.00	78.0	£POA
PH105Y	105	105	110	6.0	79.00	85.0	£POA
PH115Z	112	115	120	6.0	86.00	95.0	£POA
PH125Z	112	125	130	6.0	96.00	105.0	£POA

Minimum order value of £50 applies.

Material
535A99 (100Cr6) Through hardened Steel 62-64Rc.

Ordering Example =	PH18E	12.00
		Bore size required for order and delivery

Standard Increment Bore Sizes
From 1.0mm to 3mm in steps of 0.05mm.
From 3.0mm to 14mm in steps of 0.10mm.
From 14.0mm to 33mm in steps of 0.25mm (and including all 0.25mm and 0.75mm sizes).
From 33.0mm to 51mm in steps of 0.50mm.
From 51.0mm to 100mm in steps of 1.00mm.

Concentricity is 0.2mm on drilled or ground bores up to 1.4mm
Nitrided bushes for longer life giving a hardness of 67-69 Rockwell C are available at extra cost.

Nominal Sizes		F7 Hole		n6 Shaft		h13 Shaft
Over	Up to	High+	Low+	High+	Low+	High	Low-
-	3	16	6	10	4	0	140
3	6	22	10	16	8	0	180
6	10	28	13	19	10	0	220
10	18	34	16	23	12	0	270
18	30	41	20	28	15	0	330
30	50	50	25	33	17	0	390
50	80	60	30	39	20	0	460
80	120	71	36	45	23	0	540

Also Available
(a) Fixed & Slip Renewable: These two features are incorporated on one bush, which is used in conjunction with liner bushes, and is held in place by a lock screw, tenon or stop pin.
The bush is a slide fit in its corresponding liner.
The removable fixed feature of the bush is normally used on high production work, when the bush can be easily and quickly replaced with a minimum loss of production.
The removable slip feature of the bush is used when more than one operation is carried out, when the bush is instantly removable after each operation.
(b) Headless Liner Type: This range is for use in conjunction with Renewable Fixed and Slip type bushes.
(c) Headed Liner Type: As above but headed. The shallow head can be left standing proud or countersunk flush.

Imperial sizes for all types available.

Downloads
PDF Documents : Catalogue Page