Ondrives: Linear - Supersmart Bearings & Housings - LSB-OP LSB-OPAJ - Super Smart Ball Bushing™ Bearing Pillow Blocks Open Type

LSB-OP LSB-OPAJ : Super Smart Ball Bushing™ Bearing Pillow Blocks Open Type

Linear » Supersmart Bearings & Housings »
LSB-OP & LSB-OPAJ Type : Super Smart Ball Bushing™ Bearing Pillow Blocks Open Type Fixed & Adjustable

LSB-OP LSB-OPAJ Super Smart Ball Bushing Bearing Pillow Blocks

Discounts

1+ 0%

20+ 5%

40+ 10%

60+ 15%

100+ 20%

200+ 35%

Part Number	Ød⁽⁵⁾	H^±0.02	H1	A	A1^±0.02	B	E^±0.1	E1^±0.1	N Dia.	N2	Alpha (deg)	Mass (kg)	Dynamic Load W⁽¹⁾⁽²⁾	Load Limit Wo⁽²⁾⁽⁴⁾	Cost	Quantity	Add to Basket
FIXED
LSB-12OP	12	18	28	43	21.5	39	23	32	4.3	M5	70	0.11	750	825	£110.59
LSB-16OP	16	22	35	53	26.5	43	26	40	5.3	M6	70	0.19	2200	2400	£127.47
LSB-20OP	20	25	42	60	30.0	54	32	45	6.6	M8	50	0.30	4000	4400	£144.06
LSB-25OP	25	30	51	78	39.0	67	40	60	8.4	M10	60	0.60	6700	7300	£169.73
LSB-30OP	30	35	60	87	43.5	79	45	68	8.4	M10	55	0.93	8300	9100	£199.26
LSB-40OP	40	45	77	108	54.0	91	58	86	10.5	M12	54	1.66	13700	15000	£316.18
ADJUSTABLE
LSB-12OPAJ	12	18	28	43	21.5	39	23	32	4.3	M5	70	0.11	750	825	£119.09
LSB-16OPAJ	16	22	35	53	26.5	43	26	40	5.3	M6	70	0.19	2200	2400	£137.31
LSB-20OPAJ	20	25	42	60	30.0	54	32	45	6.6	M8	50	0.30	4000	4400	£147.04
LSB-25OPAJ	25	30	51	78	39.0	67	40	60	8.4	M10	60	0.60	6700	7300	£182.91
LSB-30OPAJ	30	35	60	87	43.5	79	45	68	8.4	M10	55	0.93	8300	9100	£214.58
LSB-40OPAJ	40	45	77	108	54.0	91	58	86	10.5	M12	54	1.66	13700	15000	£340.60

Material
Housing: Aluminium - Bearing Fitted

Other Info.
Super Smart Ball Bushing™ Bearing fitted.

Designed for use with Hard Linear Shafting (Z-A & Z-B Types) (h6 Tolerance)
(1) For rated travel life of 100km. For longer travel lives, reduce load to W x (100/Life)^0.33 where (km) is the required travel life.
Do not exceed the Dynamic Load Rating for travel life of less than 100km.
(2) The load Limit is the maximum load that may be applied to a bearing/shaft.
It is important to analyze the application so that peak and/or shock do not exceed the Load Limit.
(4) The load capacities W and W0 are valid for a resultant load applied at 90° with the ball tracks oriented as shown in the polar graphs on the Technical pages.
If the resultant acts along another direction, the appropriate multiplicative correction factor, K0, should be applied to W and W0 respectively.
Open type bearings have reduced load capacities when used in pull-off situations.
(5) Adjusted to nominal.

Standard Diametral Clearances (Closed Type)
Nom. Size Ød (mm)	Diametral Clearance (µm)
12	+26 +3
16	+26 +3
20	+30 +4
25	+30 +4
30	+30 +4
40	+35 +5