Ondrives: Linear - Linear Slides - LWL2-3 - 2-3mm Rail Load up to 609N

LWL2-3 : Load up to 609N

Linear » Linear Slides »
LWL Type : L Series : 2mm & 3mm Rail Width - Non Ball Retained

LWL Precision Linear Slides L Series

When ordering track rail, please order the correct number of carriages for your application

Discounts

1+ 0%

Part Number	Track Rail Length L	No. of Holes	Maximum Track Length	Cost	Quantity	Order
LWL2-32	32	4	104	£POA
LWL2-40	40	5		£POA
LWL2-48	48	6		£POA
LWL2-56	56	7		£POA
LWL2-64	64	8		£POA
LWL2-72	72	9		£POA
LWL2-80	80	10		£POA
LWL2-88	88	11		£POA
LWL2-96	96	12		£POA
LWL2-104	104	13		£POA
LWL2-C	Carriage (Slide Unit) (Standard Type)	-		£POA
LWL3-30	30	3	150	£24.33
LWL3-40	40	4		£26.47
LWL3-60	60	6		£30.82
LWL3-80	80	8		£35.72
LWL3-100	100	10		£41.10
LWL3-110	110	11		£43.80
LWL3-120	120	12		£47.00
LWL3-130	130	13		£50.32
LWL3-140	140	14		£53.54
LWL3-150	150	15		£56.81
LWL3-C	Carriage (Slide Unit) (Standard Type)	-		£67.57
LWLC3-C	Carriage (Slide Unit) (Short Type)	-		£56.81

	Part Number Carriage LWL2-C	Part Number Carriage LWLC3-C	Part Number Carriage LWL3-C	Figures shown in To column and upper figures of all Tx and Ty of each model number apply to one slide unit as illustrated. The values shown below the single case figures for Tx and Ty are for two slide units in close contact on the same rail.
Mass (g)
Carriage (Slide Unit)	0.9	1.0	1.6
Track Rail per 100mm	2.8	5.3	5.3
Dimensions of Assembly (mm)
H±0.020(Std.) (P±0.010)	3.2	4.0	4.0
H1	0.7	1.0	1.0
N±0.025(Std.) (P±0.015)	2.0	2.5	2.5
Dimensions of Slide Unit (mm)
W2	6	8	8
L1	12.4	12.0	16.0
L2	4.0	3.5	5.5
L3	8.8	6.7	10.7
M1 x Depth	M1.4 x 1.1 (0.10 Nm)	M1.6 x 1.3 (0.15 Nm)	M2 x 1.3 (0.31 Nm)
h1 (Slide Unit Shoulder Height)	1.0	1.2	1.2
Dimensions of Track Rail (mm)
W	2	3	3
H4	2.0	2.6	2.6
d3	M1 Thro (0.04 Nm)	M1.6 Thro (0.15 Nm)	M1.6 Thro (0.15 Nm)
h2 (Track Rail Shoulder Height)	0.5	0.8	0.8
E	4.0	5.0	5.0
F	8	10	10
Ratings
Basic Dynamic Load Rating C N	204	245	339
Basic Static Load Rating Co N	395	375	609
Static Rated Moment To Nm	0.43	0.60	0.97
Static Rated Moment Tx Nm	0.56 3.00	0.41 3.00	1.00 6.10
Static Rated Moment Ty Nm	0.67 3.60	0.49 3.50	1.20 7.20

Material
Rail, Carriage & Balls: Stainless Steel. Hardened similar to 440C
End Plates: Synthetic Resin End Seals: Rubber.

Performance : Track Rail
Max. Speed: 3m/sec.
Max. Continuous Temperature: +100°C
Max. Intermittent Temperature: +120°C

Performance : Carriage
Dimension Variation Between Carriage Slide on Same Rail (Std Grade): H=0.015, N=0.020
Dimension Variation Between Carriage Slide on Same Rail (High Precision P Grade P.O.A.): H=0.007, N=0.010
Parallelism in Operation Over: 500mm=0.012mm, 1000mm=0.018mm (A to C and D to B).
A Higher tolerance grade is available, contact Sales for details
Load Direction: If upward or downward, as table. If lateral, dynamic x 1.13 C, static x 1.19 Co.
Dynamic Rating: From a group of the same slide units, 90% achieve a distance of 50 x 10³ metres.
For temperatures over 100°C (max. 120°C) we can supply special high temperature grease (clean room quality supplied in syringe) CG2-SY.
Preload is available (To) zero to minimal clearance, zero to minimal preload, (T1) 0.02 Co preload.

Other Info.
Characteristics: Easy handling (none ball retained - balls liable to fall out if carriage removed).
Easy maintenance. Smooth operation. Low Noise. High High Accuracy. Long life. High reliability..
Lubrication: Every 6 months under general use. Every 3 months for daily use. Use a lithium-soap based grease. (Oil can be used).

Downloads
DXF Drawings (Zip archived) : LWL3-C
PDF Documents : Catalogue Pages | Technical | Full LWL Range (including Technical)