RJZM01 & RJUM01 : DryLin® R Slide Bearings - Closed Long
Linear » DryLin® R Slide Bearings & Housings »RJZM01 & RJUM01 Type : DryLin® R Slide Bearings - Closed Long
| Discounts | 1+ 0% | 6+ 5% | 20+ 10% | 40+ 15% | 60+ 20% | 100+ 30% |
| Part Number |
Shaft Ød1 |
d2 H7 |
B h10 |
B1 H10 |
s H10 |
dn h10 |
Tolerance |
pmax. (N) |
pmax. (N) |
Weight |
Cost | Quantity | Add to Basket |
| RJZM01-05* | 5 | 12 | 22 | 14.2 | 1.10 | 11.5 | 0.025 / 0.060 | 525 | 3675 | 0.005 | £22.82 |
|
|
| RJZM01-06* | 6 | 12 | 22 | 14.2 | 1.10 | 11.5 | 0.025 / 0.060 | 525 | 3675 | 0.005 | £POA |
|
|
| RJZM01-08* | 8 | 16 | 25 | 16.2 | 1.10 | 15.2 | 0.032 / 0.070 | 960 | 6720 | 0.009 | £26.22 |
|
|
| RJUM01-10 | 10 | 19 | 29 | 21.6 | 1.30 | 17.5 | 0.030 / 0.088 | 725 | 5075 | 0.014 | £20.29 |
|
|
| RJUM01-12 | 12 | 22 | 32 | 22.6 | 1.30 | 20.5 | 0.030 / 0.088 | 960 | 6720 | 0.021 | £22.82 |
|
|
| RJUM01-16 | 16 | 26 | 36 | 24.6 | 1.30 | 24.2 | 0.030 / 0.088 | 1440 | 10080 | 0.028 | £26.50 |
|
|
| RJUM01-20 | 20 | 32 | 45 | 31.2 | 1.60 | 29.6 | 0.030 / 0.091 | 2250 | 15750 | 0.049 | £31.07 |
|
|
| RJUM01-25 | 25 | 40 | 58 | 43.7 | 1.85 | 36.5 | 0.030 / 0.091 | 3625 | 25375 | 0.108 | £39.67 |
|
|
| RJUM01-30 | 30 | 47 | 68 | 51.7 | 1.85 | 43.5 | 0.040 / 0.110 | 5100 | 35700 | 0.162 | £51.69 |
|
|
| RJUM01-40 | 40 | 62 | 80 | 60.3 | 2.15 | 57.8 | 0.040 / 0.115 | 8000 | 56000 | 0.334 | £85.86 |
|
|
| RJUM01-50 | 50 | 75 | 100 | 77.3 | 2.65 | 70.5 | 0.050 / 0.130 | 12500 | 87500 | 0.579 | £128.16 |
|
Material
Case:
Aluminium
Bearing: DryLin® R (* Supplied with press fitted cylindrical bearings). Replacements available.
Performance
Maximum Mean Surface Pressure:
25 N/mm2
Highest Wear Resistance at loads: < 2 N/mm2
Recommended Tolerance for Mating Shaft: h6-h10
Maximum Speed: 8 m/s (dry) >10 m/s (lubricated) 1.5 m/s (rotating dry)
Working Temperature Range: -60°C to +100°C (increased wear when used in excess of 80°C).
Special Features
Enclosed anodized aluminum adapter.
Dimensions corresponding to the standard for recirculating ball bearings.
Recommended housing bore H7.
For use with circlips according to DIN 471 and/or 472 (not included)
Other Info.
Best coefficients of friction are with hard ground shafting 50 HRC 0.2 µm Finish,
but friction figures are only marginally higher for other shafts.
For use with DryLin® R: AWM Type Aluminium Shafts.
Downloads
PDF Documents : Catalogue Page | DryLin® R Technical | Complete DryLin® R Sliding Bearings Range
Copyright © Ondrives Ltd 2012. All Rights Reserved. Powered By multisys Liaison™ | Login