Ondrives: Couplings - Flexible Drive Shafts - FD16 & FDQ16 16mm Bores 12.5-50Nm

FD16 FDQ16 : 16mm Bores 12.5-50Nm

Couplings » Flexible Drive Shafts »
FD16 & FDQ16 Type : 16mm bores - 12.50Nm-50.00Nm

FD16 FDQ16 Masterflex Flexible Drive Shaft with Oilite Bushes or Ball Bearings

Discounts

1+ 0%

5+ 5%

25+ 10%

Part Number	Bore	Direction	Max Speed Rpm	Shaft Length	Bearings/ Bushes	Cost	Quantity	Add to Basket
FD16500	Ø15	A	4000	500	Ball Bearings	£303.75
		B	2000			£303.75
		C	4000			£303.75
FDQ16500	Ø15	A	2000	500	Oilite Bushes	£254.59
		B	200			£254.59
		C	2000			£254.59
FD161000	Ø15	A	4000	1000	Ball Bearings	£366.18
		B	2000			£366.18
		C	4000			£366.18
FDQ161000	Ø15	A	2000	1000	Oilite Bushes	£317.04
		B	200			£317.04
		C	2000			£317.04
FD161500	Ø15	A	4000	1500	Ball Bearings	£428.58
		B	2000			£428.58
		C	4000			£428.58
FDQ161500	Ø15	A	2000	1500	Oilite Bushes	£379.46
		B	200			£379.46
		C	2000			£379.46
FD162000	Ø15	A	4000	2000	Ball Bearings	£491.06
		B	2000			£491.06
		C	4000			£491.06
FDQ162000	Ø15	A	2000	2000	Oilite Bushes	£441.90
		B	200			£441.90
		C	2000			£441.90
FD162500	Ø15	A	4000	2500	Ball Bearings	£559.93
		B	2000			£559.93
		C	4000			£559.93
FDQ162500	Ø15	A	2000	2500	Oilite Bushes	£504.89
		B	200			£504.89
		C	2000			£504.89
FD163000	Ø15	A	4000	3000	Ball Bearings	£615.89
		B	2000			£559.93
		C	4000			£559.93
FDQ163000	Ø15	A	2000	3000	Oilite Bushes	£567.17
		B	200			£567.17
		C	2000			£567.17

A = Anti-clockwise rotation, B = Bi-direction rotation, C = Clockwise rotation (standard)

Direction	Min. Operating Radius	Torsional Deflection (0.1Nm Load at 1m Length		Max Torque (Nm) v Bend radius (mm)
Direction	Min. Operating Radius	Wind	Unwind	300mm	350mm	500mm	600mm	800mm	1000mm
A & C	300	0.27°	0.23°	12.50Nm	14.00Nm	16.00Nm	18.00Nm	20.00Nm	25.00Nm
B	300	0.06°	0.13°	20.00Nm	28.00Nm	35.00Nm	40.00Nm	45.00Nm	50.00Nm

Material
Shafts & Ends: Steel 070M420 with plastic cover
End Type:
M = Supplied both ends as standard (FD Type - Ball Bearing)
R = Supplied both ends as standard (FDQ Type - Oilite Bush)
Please specify end option if required different.
Eg. MN, NN / RS, SS
The flexible core has a layer of grease for lubrication in operations of continuous usage eg. an 8 hour day.
We recommend you regrease and check the flexible centre every 3 months.
The knurled ends unscrew to allow the shaft to come out. Re-seal after inspection
Spare flexible centres can be purchased to replace broken or worn examples.

Downloads

PDF Documents : Catalogue Page | Technical | Full Range (inc. Technical)