Ondrives: Couplings - Clamps and Collars - MLR-C : Aluminium 6-14mm bores

MLR-C : Long Rigid Couplings (Aluminium & Clamp) 6-15mm Bores

Couplings » Clamps and Collars »
MLR-C : Aluminium Long Version (Clamp Type)

Discounts

1+ 0%

6+ 10%

16+ 15%

41+ 20%

100+ 25%

200+ 30%

400+ 35%

Part Number	Standard Bores		Max. Bore	ØA	L	W	F₁	F₂	G	M	Wrench Torque (Nm)	Rated Torque (Nm)	Max. Torque (Nm)	Max. Speed (rpm)	Moment of Inertia (kg-m²)	Mass (g)	Cost	Quantity	Add to Basket
Part Number	ØD₁	ØD₂	Max. Bore	ØA	L	W	F₁	F₂	G	M	Wrench Torque (Nm)	Rated Torque (Nm)	Max. Torque (Nm)	Max. Speed (rpm)	Moment of Inertia (kg-m²)	Mass (g)	Cost	Quantity	Add to Basket
MLR-16C	6	6	6	16	11	22	2.5	5.5	5	M2	0.5	0.3	0.6	9000	3.4 x 10^-7	10	£18.01
MLR-20C	8	8	8	20	12	24	2.5	6.0	7	M2	0.5	0.5	1.0	7000	9.2 x 10^-7	18	£20.35
MLR-25C	10	10	12	25	18	36	4.5	9.0	9	M2.5	1.0	1.0	2.0	6000	3.4 x 10^-6	38	£22.55
MLR-32C	14	14	15	32	20	40	4.0	10.0	11	M3	1.5	2.0	4.0	4500	1.0 x 10^-5	70	£29.35

* Moment of inertia and mass figures based on the maximum shaft bores.

Material
Aluminium alloy, Anodic Oxide coated
The maximum torque of the miniature coupling is two-fold of the rated torque.
Select a type in which torque generated during continuous operation does not exceed the rated torque of the miniature coupling.
Can be bored out for larger bore sizes.
Maintenance-free and excellent resistance to oil and chemicals
Recommended tolerance on shaft diameters is h6 and h7
Maximum Temperature: 100°C (approx.)

Features
Long type rigid coupling - Can be used as a joint to connect with shafts.

Other Info.
These rigid couplings transmit the torque and rotational angles while absorbing misalignments. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Make sure to adjust the alignment accordingly.
There are three types of shaft misalignment, namely in terms of parallel misalignment, angular misalignment and shaft end-play. Adjust the alignment to be below allowable values listed in the specification table.
The maximum misalignment is the allowable value when only one of the misalignments exists alone. In case two or more misalignments exist at the same time, the allowable values shall be less than half of the maximum misalignment listed in the specification table.
We recommend you to adjust the shaft misalignment to be below 1/3 of maximum values for the elongation of the life of the coupling.
IMPORTANT:- Couplings and other rotational parts should be protected by covers for safety operation. Also, take note that operation under misalignment exceeding maximum values and excessive torque may result in shorter life of the coupling due to plastic deformation.

Downloads
PDF Documents : Catalogue Page