Ondrives: Couplings - Beam Couplings - MWS : Aluminium 2-8mm bores

MWS : Aluminium 2-8mm bores

Couplings » Beam Couplings »
MWS : Aluminium 4 Slit (with Set Screw)

MWS : Aluminium 4 Slit (with Set Screw)

Discounts

1+ 0%

6+ 10%

16+ 15%

41+ 20%

100+ 25%

200+ 30%

400+ 35%

Part Number	Standard Bores		Max. Bore	ØA	L	W	F	M	Mass (g)	Wrench Torque (Nm)	Rated Torque (Nm)	Max. Torque (Nm)	Max. rpm (min^–1)	Moment of Inertia (kg-m²)	Static Torsional Stiffness (Nm/rad)	Max. Angular Offset	Max. Axial End–Play	Cost	Quantity	Add to Basket
Part Number	ØD₁	ØD₂	Max. Bore	ØA	L	W	F	M	Mass (g)	Wrench Torque (Nm)	Rated Torque (Nm)	Max. Torque (Nm)	Max. rpm (min^–1)	Moment of Inertia (kg-m²)	Static Torsional Stiffness (Nm/rad)	Max. Angular Offset	Max. Axial End–Play	Cost	Quantity	Add to Basket
MWS-8	2	2	4	8	3.40	10	1.7	M2	1.0	0.3	0.1	0.2	48,000	1.0 x 10^-8	24	1°	±0.1	£17.47
MWS-12	4	4	6	12	5.20	14	2.5	M2.5	3.1	0.5	0.2	0.4	32,000	7.0 x 10^-8	60	1°	±0.1	£19.59
MWS-16	5	5	8	16	6.80	18	3.0	M3	7.4	0.7	0.3	0.6	24,000	2.8 x 10^-7	110	1°	±0.2	£21.55
MWS-20	5	6	10	20	7.65	20	3.0	M3	12.0	0.7	0.5	1.0	19,000	7.5 x 10^-7	130	1°	±0.2	£23.15
MWS-25	5	6	12	25	9.60	25	4.0	M4	24.0	1.7	1.0	2.0	15,000	2.3 x 10^-6	350	1°	±0.2	£27.00
MWS-32	8	8	16	32	12.60	32	6.0	M4	50.0	1.7	2.0	4.0	12,000	8.0 x 10^-6	650	1°	±0.2	£33.66

The maximum torque of the miniature coupling is two-fold of the rated torque.
Select a type in which torque generated during continuous operation does not exceed the rated torque of the miniature coupling.

Material
Aluminium alloy, Anodic Oxide coated
Max. Temperature (approx.): 100°C.

Ordering
Please advise required bores when ordering.
The MWS coupling can be bored out for larger bore sizes.

Features
Maintenance free and excellent resistance to oil and chemicals
Ideal one-piece metallic spring coupling
Light weight, short length coupling
High torsional stiffness and response
Zero backlash
Moment of low inertia
Complete absorption of angular misalignment and shaft end-play by spring action
Parallel misalignment is not absorbed
Identical clockwise and anti-clockwise rotational characteristics

Other Info.
Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Make sure to adjust the alignment accordingly.
There are three types of shaft misalignment, namely in terms of parallel misalignment, angular misalignment and shaft end-play. Adjust the alignment to be below allowable values listed in the specification table of each miniature coupling. The maximum misalignment listed within this range is the allowable value only when one of the misalignments exists. In case two or more misalignments exist at the same time, the allowable values will be less than 50% of the maximum misalignment listed in the specification tables. Misalignments are sometimes caused not only by equipment assembly, but also by vibration, heat expansion, wear of bearings, etc during operation. Therefore, it is recommended to adjust the shaft misalignment to be below 1/3 of maximum values.
IMPORTANT:- Couplings and other rotational parts should be protected by covers for safety operation. Also, take note that operation under misalignment exceeding maximum values and excessive torque may result in shorter life of the coupling due to plastic deformation.

Downloads
PDF Documents : Catalogue Page