MSX : Set Screw Fixing 5-14mm bores
Couplings » Beam Couplings »
MSX : Duralumin 6 Slit (with Set Screw)
| Discounts | 1+ 0% | 6+ 10% | 16+ 15% | 41+ 20% | 100+ 25% | 200+ 30% | 400+ 35% |
| Part Number |
Standard Bores |
Max. Bore |
ØA | L | W | F | M | Mass (g) |
Wrench Torque (Nm) |
Rated Torque (Nm) |
Max. Torque (Nm) |
Max. rpm (min–1) |
Moment of Inertia (kg-m2) |
Static Torsional Stiffness (Nm/rad) |
Max Parallel Offset |
Max Angular Offset |
Max Axial End–Play |
Cost | Quantity | Add to Basket |
|
| ØD1 | ØD2 | ||||||||||||||||||||
| MSX-16 | 5 | 5 | 8 | 16 | 6.0 | 17.4 | 3.00 | M3 | 7 | 0.7 | 0.5 | 1 | 39,000 | 2.8 x 10-7 | 200 | 0.05 | 0.5° | ±0.1 | £28.52 |
|
|
| MSX-19 | 5 | 5 | 10 | 19 | 6.8 | 20.0 | 3.40 | M3 | 10 | 0.7 | 1.0 | 2 | 33,000 | 6.2 x 10-7 | 270 | 0.05 | 0.5° | ±0.1 | £28.67 |
|
|
| MSX-24 | 6 | 6 | 12 | 24 | 8.5 | 25.0 | 4.25 | M4 | 22 | 1.7 | 1.5 | 3 | 26,000 | 2.0 x 10-6 | 790 | 0.05 | 0.5° | ±0.1 | £34.46 |
|
|
| MSX-29 | 8 | 8 | 14 | 29 | 10.2 | 30.0 | 5.10 | M4 | 40 | 1.7 | 2.0 | 4 | 21,000 | 5.2 x 10-6 | 1400 | 0.05 | 0.5° | ±0.1 | £40.74 |
|
|
| MSX-34 | 10 | 14 | 18 | 34 | 12.0 | 35.0 | 6.00 | M5 | 64 | 4.0 | 3.0 | 6 | 18,000 | 1.1 x 10-5 | 2200 | 0.05 | 0.5° | ±0.1 | £49.60 |
|
|
| MSX-39 | 10 | 14 | 20 | 39 | 13.5 | 40.0 | 6.75 | M5 | 90 | 4.0 | 6.0 | 12 | 16,000 | 2.9 x 10-5 | 4100 | 0.05 | 0.5° | ±0.1 | £61.09 |
|
|
| MSX-44 | 12 | 12 | 22 | 44 | 15.5 | 45.0 | 7.75 | M6 | 133 | 7.0 | 9.0 | 18 | 14,000 | 5.5 x 10-5 | 5100 | 0.05 | 0.5° | ±0.1 | £72.11 |
|
|
Select a type in which torque generated during continuous operation does not exceed the rated torque of the miniature coupling.
Material
Extra Super Duralumin (the highest strength aluminium alloy), Anodic Oxide coated.
Max. Temperature (approx.): 100°C.
Recommended tolerance on shaft diameters is h6 and h7.
Tolerance on shaft bores of setscrew type is H8.
Extremely high torsional stiffness, low inertia and excellent response.
Zero backlash.
Ordering
Please advise required bores when ordering.
The MSX coupling can be bored out for larger bore sizes.
Keyways can be machined on request - POA
Features
Absorption of parallel, angular misalignments and shaft end-play by spring action.
Identical clockwise and anticlockwise rotational characteristics.
Maintenance-free, oil and chemical resistant.
Lightweight -
Compact
Ideally suited for servomotor applications
Other Info.
Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Make sure to adjust the alignment accordingly.
There are three types of shaft misalignment, namely in terms of parallel misalignment, angular misalignment and shaft end-play. Adjust the alignment to be below allowable values listed in the specification table of each miniature coupling. The maximum misalignment listed within this range is the allowable value only when one of the misalignments exists. In case two or more misalignments exist at the same time, the allowable values will be less than 50% of the maximum misalignment listed in the specification tables. Misalignments are sometimes caused not only by equipment assembly, but also by vibration, heat expansion, wear of bearings, etc during operation. Therefore, it is recommended to adjust the shaft misalignment to be below 1/3 of maximum values.
IMPORTANT:- Couplings and other rotational parts should be protected by covers for safety operation. Also, take note that operation under misalignment exceeding maximum values and excessive torque may result in shorter life of the coupling due to plastic deformation.
Downloads
PDF Documents : Catalogue Page
Copyright © Ondrives Ltd 2012. All Rights Reserved. Powered By multisys Liaison™ | Login