MSM : Plain Iglidur® M250 Thick Bearings (6-30mm Bores)
Bearings » Bushings »MSM Type : Plain Iglidur® M250 Thick Bearings - 6mm-30mm Bore Dias.
| Discounts | 1+ 0% | 10+ 5% | 25+ 10% | 50+ 15% | 100+ 20% | 200+ 25% | 500+ 30% | 1000+ 40% | 2000+ 45% |
| Part Number |
d1* E10 |
d2 | b1 h13 | Running
Clearance with h9 Shaft and H7 Housing |
Cost | Quantity | Add to Basket |
|
| Max. | Min. | |||||||
| MSM0610-06 | +0.030 6+0.105 |
10 | 6 | 0.135 | 0.030 | £2.01 |
|
|
| MSM0610-10 | +0.030 6+0.105 |
10 | 10 | 0.135 | 0.030 | £2.13 |
|
|
| MSM0612-06 | +0.030 6 +0.105 |
12 | 6 | 0.135 | 0.030 | £2.13 |
|
|
| MSM0612-10 | +0.030 6 +0.105 |
12 | 10 | 0.135 | 0.030 | £2.24 |
|
|
| MSM0811-08 | +0.030 8+0.105 |
11 | 8 | 0.166 | 0.040 | £2.13 |
|
|
| MSM0812-08 | +0.040 8+0.130 |
12 | 8 | 0.166 | 0.040 | £2.13 |
|
|
| MSM0812-10 | +0.040 8+0.130 |
12 | 10 | 0.166 | 0.040 | £2.24 |
|
|
| MSM0814-10 | +0.040 8+0.130 |
14 | 6 | 0.166 | 0.040 | £2.24 |
|
|
| MSM1014-06 | +0.040 10+0.130 |
14 | 6 | 0.166 | 0.040 | £2.01 |
|
|
| MSM1014-10 | +0.040 10+0.130 |
14 | 10 | 0.166 | 0.040 | £2.13 |
|
|
| MSM1016-06 | +0.040 10+0.130 |
16 | 6 | 0.166 | 0.040 | £2.13 |
|
|
| MSM1216-20 | +0.050 12+0.160 |
16 | 20 | 0.203 | 0.050 | £2.24 |
|
|
| MSM1218-10 | +0.050 12+0.160 |
18 | 10 | 0.203 | 0.050 | £2.24 |
|
|
| MSM1218-20 | +0.050 12+0.160 |
18 | 20 | 0.203 | 0.050 | £2.38 |
|
|
| MSM1420-10 | +0.050 14+0.160 |
20 | 10 | 0.203 | 0.050 | £2.38 |
|
|
| MSM1521-10 | +0.050 15+0.160 |
21 | 10 | 0.203 | 0.050 | £2.38 |
|
|
| MSM1521-20 | +0.050 15+0.160 |
21 | 20 | 0.203 | 0.050 | £2.61 |
|
|
| MSM1620-20 | +0.050 16+0.160 |
20 | 20 | 0.203 | 0.050 | £2.38 |
|
|
| MSM1620-25 | +0.050 16+0.160 |
20 | 25 | 0.203 | 0.050 | £2.61 |
|
|
| MSM1622-15 | +0.050 16+0.160 |
22 | 15 | 0.203 | 0.050 | £2.61 |
|
|
| MSM1622-25 | +0.050 16+0.160 |
22 | 25 | 0.203 | 0.050 | £2.99 |
|
|
| MSM2025-20 | +0.065 20+0.195 |
25 | 20 | 0.247 | 0.065 | £2.50 |
|
|
| MSM2025-30 | +0.065 20+0.195 |
25 | 30 | 0.247 | 0.065 | £3.12 |
|
|
| MSM2026-20 | +0.065 20+0.195 |
26 | 20 | 0.247 | 0.065 | £2.99 |
|
|
| MSM2026-30 | +0.065 20+0.195 |
26 | 30 | 0.247 | 0.065 | £3.35 |
|
|
| MSM2530-20 | +0.065 25+0.195 |
30 | 20 | 0.247 | 0.065 | £2.86 |
|
|
| MSM2530-30 | +0.065 25+0.195 |
30 | 30 | 0.247 | 0.065 | £3.35 |
|
|
| MSM2532-20 | +0.065 25+0.195 |
32 | 20 | 0.247 | 0.065 | £3.58 |
|
|
| MSM2532-30 | +0.065 25+0.195 |
32 | 30 | 0.247 | 0.065 | £4.20 |
|
|
| MSM3038-20 | +0.065 30+0.195 |
38 | 20 | 0.247 | 0.065 | £4.04 |
|
|
| MSM3038-30 | +0.065 30+0.195 |
38 | 30 | 0.247 | 0.065 | £4.80 |
|
|
* Tolerance when fitted (Dimensions following DIN 1494). Designed to fit H7 Housing and h7-h9 Shaft.
Material
Iglidur® M250 Impact Resistant Thermo-plastic
Performance
Max. Cont. Speed: (dry operation) Rotating 1m/s Oscillating 1m/s Linear 3m/s
Temperature Range: -40°C to +115°C Short period 200°C
Static pressure loads at 115°C: 12N/mm2
Max P.V Value: during dry operation is 0.3 max. (N/mm2 x m/s) Values upto 2 max (N/mm2 x m/s) with lubrication.
| Pressure (N) | Rpm / (Bore Ų x  ) |
|||
| (Load) N/mm2 |
|
(Velocity) m/s = |
|
|
| Bore Ų x Length (mm) | 60 |
Co-efficient of Friction against steel shaft (50 HRC 1µm) Dry 0.18 - 0.30 Grease 0.09 Oil/Water 0.04
Recommended Running Shaft to be Hard Steel 50 HRC 1.5-3µm Finish.
Downloads
PDF Documents : Catalogue Pages | Iglidur® Bearings Technical | Full Range of Iglidur Bushings
Copyright © Ondrives Ltd 2012. All Rights Reserved. Powered By multisys Liaison™ | Login