JSM : Plain Iglidur® J Bearings (14-50mm Bores)
Bearings » Bushings »JSM Type : Plain Iglidur® J Bearings - 14mm-50mm Bore Dias.
| Discounts | 1+ 0% | 10+ 5% | 25+ 10% | 50+ 15% | 100+ 20% | 200+ 25% | 500+ 30% | 1000+ 40% | 2000+ 45% |
| Part Number |
d1* E10 | d2 | b1 (h13) | Running
Clearance with h9 Shaft and H7 Housing |
Cost | Quantity | Add to Basket |
|
| Max. | Min. | |||||||
| JSM1416-10 |
+0.032 14 +0.102 |
16 | 10 | 0.145 | 0.032 | £5.07 |
|
|
| JSM1416-15 |
+0.032 14 +0.102 |
16 | 15 | 0.145 | 0.032 | £5.48 |
|
|
| JSM1416-25 |
+0.032 14 +0.102 |
16 | 25 | 0.145 | 0.032 | £6.66 |
|
|
| JSM1418-18 |
+0.032 14 +0.102 |
18 | 18 | 0.145 | 0.032 | £6.78 |
|
|
| JSM1517-12 |
+0.032 15 +0.102 |
17 | 12 | 0.145 | 0.032 | £5.07 |
|
|
| JSM1517-20 |
+0.032 15 +0.102 |
17 | 20 | 0.145 | 0.032 | £6.27 |
|
|
| JSM1618-12 |
+0.032 16 +0.102 |
18 | 12 | 0.145 | 0.032 | £6.27 |
|
|
| JSM1618-20 |
+0.032 16 +0.102 |
18 | 20 | 0.145 | 0.032 | £7.57 |
|
|
| JSM1820-20 |
+0.032 18 +0.102 |
20 | 20 | 0.145 | 0.032 | £9.28 |
|
|
| JSM2023-20 |
+0.040 20+0.124 |
23 | 20 | 0.176 | 0.040 | £10.34 |
|
|
| JSM2023-25 |
+0.040 20 +0.124 |
23 | 25 | 0.176 | 0.040 | £11.38 |
|
|
| JSM2026-30 |
+0.040 20 +0.124 |
26 | 30 | 0.176 | 0.040 | £12.71 |
|
|
| JSM2226-15 |
+0.040 22 +0.124 |
26 | 15 | 0.176 | 0.040 | £12.83 |
|
|
| JSM2427-25 |
+0.032 24+0.102 |
27 | 25 | 0.176 | 0.040 | £12.16 |
|
|
| JSM2528-30 |
+0.040 25 +0.124 |
28 | 30 | 0.176 | 0.040 | £13.09 |
|
|
| JSM2630-20 |
+0.040 26 +0.124 |
30 | 25 | 0.176 | 0.040 | £13.48 |
|
|
| JSM3034-25 |
+0.040 30 +0.124 |
34 | 25 | 0.176 | 0.040 | £11.00 |
|
|
| JSM3034-30 |
+0.040 30 +0.124 |
34 | 30 | 0.176 | 0.040 | £12.04 |
|
|
| JSM3539-20 |
+0.050 35+0.150 |
39 | 20 | 0.212 | 0.050 | £10.36 |
|
|
| JSM4044-40 |
+0.050 40+0.150 |
44 | 40 | 0.212 | 0.050 | £17.59 |
|
|
| JSM5055-50 |
+0.050 50+0.150 |
55 | 50 | 0.212 | 0.050 | £32.77 |
|
|
* Tolerance when fitted (Dimensions following DIN 1494). Designed to fit H7 Housing and h7-h9 Shaft.
Material
Iglidur® J Plastic Colour yellow
Performance
Max. Cont. Speed (dry operation) Rotating 1.5m/s. Oscillating 1.5m/s. Linear 8m/s.
Temperature Range -40°C to +100°C Short period 120°C
Ideal Conditions: Load < 2N/mm2 Temp +60°C max
Static Pressure Loads at 20°C 35N/mm2
Max P.V valve during dry operation is 1N/mm2 x m/s
Iglidur® J is designed for dry operation but P.V value is increased with continuous lubrication in oil, grease, water or other liquids.
| Pressure (N) | Rpm / (Bore Ų x  ) |
|||
| (Load) N/mm2 | (Velocity) m/s = | |||
| Bore Ų x Length (mm) | 60 |
Co-efficient of friction against steel shaft (50 HRC 0.2µm): Dry: 0.06 - 0.18. Grease: 0.09. Oil/Water: 0.04.
Recommended Running Shaft to be Hard Steel 50 HRC 0.8-2µm Finish
Softer shafts can work well on these bushings.
Moisture Absorption at RH50/23°C = 0.2%. Density: 1.5g/cm3
Downloads
PDF Documents : Catalogue Pages | Iglidur® Bearings Technical | Full Range of Iglidur Bushings
Copyright © Ondrives Ltd 2012. All Rights Reserved. Powered By multisys Liaison™ | Login