JFM : Flanged Iglidur® J Bearings (3-70mm Bores)
Bearings » Bushings »JFM Type : Flanged Iglidur® J Bearings - 3mm-70mm Bores
| Discounts | 1+ 0% | 10+ 5% | 25+ 10% | 50+ 15% | 100+ 20% | 200+ 25% | 500+ 30% | 1000+ 40% | 2000+ 45% |
| Part Number |
d1* E10 |
d2 | d3 d13 | b1 h13 | b2 -0.14 | Max. | Min. | Cost | Quantity | Add to Basket |
| JFM0304-05 | +0.010 3+0.054 |
4.5 | 7.5 | 5 | 0.75 | 0.079 | 0.014 | £3.83 |
|
|
| JFM0405-06 | +0.020 4+0.068 |
5.5 | 9.5 | 6 | 0.75 | 0.098 | 0.020 | £3.97 |
|
|
| JFM0507-05 | +0.020 5+0.068 |
7.0 | 11.0 | 5 | 1.00 | 0.098 | 0.020 | £4.09 |
|
|
| JFM0608-06 | +0.020 6+0.068 |
8.0 | 12.0 | 6 | 1.00 | 0.098 | 0.020 | £4.22 |
|
|
| JFM0608-10 | +0.020 6+0.068 |
8.0 | 12.0 | 10 | 1.00 | 0.098 | 0.020 | £4.48 |
|
|
| JFM0810-06 | +0.025 8+0.083 |
10.0 | 15.0 | 6 | 1.00 | 0.119 | 0.025 | £3.72 |
|
|
| JFM0810-08 | +0.025 8 +0.083 |
10.0 | 15.0 | 8 | 1.00 | 0.119 | 0.025 | £4.37 |
|
|
| JFM0810-10 | +0.025 8 +0.083 |
10.0 | 15.0 | 10 | 1.00 | 0.119 | 0.025 | £5.38 |
|
|
| JFM1012-05 | +0.025 10+0.083 |
12.0 | 18.0 | 5 | 1.00 | 0.119 | 0.025 | £5.00 |
|
|
| JFM1012-09 | +0.025 10+0.083 |
12.0 | 18.0 | 9 | 1.00 | 0.119 | 0.025 | £5.27 |
|
|
| JFM1012-12 | +0.025 10+0.083 |
12.0 | 18.0 | 12 | 1.00 | 0.119 | 0.025 | £5.38 |
|
|
| JFM1012-15 | +0.025 10+0.083 |
12.0 | 18.0 | 15 | 1.00 | 0.119 | 0.025 | £5.51 |
|
|
| JFM1214-09 | +0.032 12+0.102 |
14.0 | 20.0 | 9 | 1.00 | 0.145 | 0.032 | £6.15 |
|
|
| JFM1214-12 | +0.032 12+0.102 |
14.0 | 20.0 | 12 | 1.00 | 0.145 | 0.032 | £6.41 |
|
|
| JFM1214-15 | +0.032 12+0.102 |
14.0 | 20.0 | 15 | 1.00 | 0.145 | 0.032 | £6.83 |
|
|
| JFM1416-12 | +0.032 14+0.102 |
16.0 | 22.0 | 12 | 1.00 | 0.145 | 0.032 | £7.19 |
|
|
| JFM1416-17 | +0.032 14+0.102 |
16.0 | 22.0 | 17 | 1.00 | 0.145 | 0.032 | £7.71 |
|
|
| JFM1521-20 | +0.032 15+0.102 |
21.0 | 27.0 | 20 | 3.00 | 0.145 | 0.032 | £13.27 |
|
|
| JFM1618-17 | +0.032 16+0.102 |
18.0 | 24.0 | 17 | 1.00 | 0.145 | 0.032 | £8.22 |
|
|
| JFM1820-22 | +0.032 18+0.102 |
20.0 | 26.0 | 22 | 1.00 | 0.145 | 0.032 | £9.12 |
|
|
| JFM2023-21 | +0.040 20+0.124 |
23.0 | 30.0 | 21 | 1.00 | 0.176 | 0.040 | £10.67 |
|
|
| JFM2528-21 | +0.040 25+0.124 |
28.0 | 35.0 | 21 | 1.50 | 0.176 | 0.040 | £11.10 |
|
|
| JFM3034-26 | +0.040 30+0.124 |
34.0 | 42.0 | 26 | 2.00 | 0.176 | 0.040 | £11.28 |
|
|
| JFM4044-40 | +0.050 40+0.150 |
44.0 | 52.0 | 40 | 2.00 | 0.176 | 0.040 | £21.92 |
|
|
| JFM5055-50 | +0.050 50+0.150 |
55.0 | 63.0 | 50 | 2.00 | 0.176 | 0.040 | £39.98 |
|
|
| JFM7075-50 | +0.060 70+0.180 |
75.0 | 83.0 | 50 | 2.00 | - | - | £44.63 |
|
* Tolerance when fitted (Dimensions following DIN 1494). Designed to fit H7 Housing and h7-h9 Shaft.
Material
Iglidur® J Plastic Colour yellow
Performance
Max. Cont. Speed (dry operation) Rotating 1.5m/s. Oscillating 1.5m/s. Linear 8m/s.
Temperature Range -40°C to +100°C Short period 120°C
Ideal Conditions: Load < 2N/mm2 Temp +60°C max
Static Pressure Loads at 20°C 35N/mm2
Max P.V valve during dry operation is 1N/mm2 x m/s
Iglidur® J is designed for dry operation but P.V value is increased with continuous lubrication in oil, grease, water or other liquids.
| Pressure (N) | Rpm / (Bore Ų x  ) |
|||
| (Load) N/mm2 | (Velocity) m/s = | |||
| Bore Ų x Length (mm) | 60 |
Co-efficient of friction against steel shaft (50 HRC 0.2µm): Dry: 0.06 - 0.18. Grease: 0.09. Oil/Water: 0.04.
Recommended Running Shaft to be Hard Steel 50 HRC 0.8-2µm Finish
Softer shafts can work well on these bushings.
Moisture Absorption at RH50/23°C = 0.2%. Density: 1.5g/cm3
Downloads
PDF Documents : Catalogue Pages | Iglidur® Bearings Technical | Full Range of Iglidur Bushings
Copyright © Ondrives Ltd 2012. All Rights Reserved. Powered By multisys Liaison™ | Login