GFM : Flanged Iglidur® G Bearings (6-30mm Bores)
Bearings » Bushings »GFM Type : Flanged Iglidur® G Bearings - 6mm-30mm Bore Dias.
| Discounts | 1+ 0% | 10+ 5% | 25+ 10% | 50+ 15% | 100+ 20% | 200+ 25% | 500+ 30% | 1000+ 40% | 2000+ 45% |
| Part Number |
d1* E10 |
d2 | d3 d13 | b1 (h13) | b2 (-0.14) | Running Clearance with h9 Shaft and H7 Housing |
Cost | Quantity | Add to Basket |
|
| Max. | Min. | |||||||||
| GFM0608-06 | +0.020 6+0.068 |
8 | 12 | 6.0 | 1.0 | 0.098 | 0.020 | £2.13 |
|
|
| GFM0608-10 | +0.020 6 +0.068 |
8 | 12 | 10.0 | 1.0 | 0.098 | 0.020 | £2.13 |
|
|
| GFM0810-09 | +0.025 8+0.083 |
10 | 15 | 9.5 | 1.0 | 0.119 | 0.025 | £2.24 |
|
|
| GFM0810-10 | +0.025 8+0.083 |
10 | 15 | 10.0 | 1.0 | 0.119 | 0.025 | £2.24 |
|
|
| GFM1012-05 | +0.025 10+0.083 |
12 | 18 | 5.0 | 1.0 | 0.119 | 0.025 | £POA |
|
|
| GFM1012-10 | +0.025 10+0.083 |
12 | 18 | 10.0 | 1.0 | 0.119 | 0.025 | £2.50 |
|
|
| GFM1012-15 | +0.025 10+0.083 |
12 | 18 | 15.0 | 1.0 | 0.119 | 0.025 | £2.74 |
|
|
| GFM1214-09 | +0.032 12+0.102 |
14 | 20 | 9.0 | 1.0 | 0.145 | 0.032 | £3.58 |
|
|
| GFM1214-10 | +0.032 12+0.102 |
14 | 20 | 10.0 | 1.0 | 0.145 | 0.032 | £POA |
|
|
| GFM1214-15 | +0.032 12+0.102 |
14 | 20 | 15.0 | 1.0 | 0.145 | 0.032 | £3.82 |
|
|
| GFM1214-20 | +0.032 12+0.102 |
14 | 20 | 20.0 | 1.0 | 0.145 | 0.032 | £3.96 |
|
|
| GFM1416-12 | +0.032 14+0.102 |
16 | 22 | 12.0 | 1.0 | 0.145 | 0.032 | £3.69 |
|
|
| GFM1416-17 | +0.032 14+0.102 |
16 | 22 | 17.0 | 1.0 | 0.145 | 0.032 | £3.96 |
|
|
| GFM1618-17 | +0.032 16+0.102 |
18 | 24 | 17.0 | 1.0 | 0.145 | 0.032 | £3.96 |
|
|
| GFM1820-17 | +0.032 18+0.102 |
20 | 26 | 17.0 | 1.0 | 0.176 | 0.040 | £4.20 |
|
|
| GFM2023-21 | +0.040 20+0.124 |
23 | 30 | 21.5 | 1.5 | 0.176 | 0.040 | £5.39 |
|
|
| GFM2528-21 | +0.040 25+0.124 |
28 | 35 | 21.5 | 1.5 | 0.176 | 0.040 | £5.88 |
|
|
| GFM3034-26 | +0.040 30+0.124 |
34 | 42 | 26.0 | 2.0 | 0.176 | 0.040 | £8.64 |
|
|
| GFM3034-37 | +0.040 30+0.124 |
34 | 42 | 37.0 | 2.0 | 0.176 | 0.040 | £10.83 |
|
|
* Tolerance when fitted (Dimensions following DIN 1494). Designed to fit H7 Housing and h7-h9 Shaft.
Material
Iglidur® G Plastic
Performance
Max. Continuous Speed: (dry operation) Rotating 1m/s Oscillating 1.5m/s Linear 4m/s
Temperature Range: -40°C to +130°C Short period 220°C
Static pressure loads at: 130°C 60N/mm2 50°C 70N/mm2 20°C 80N/mm2
Max P.V valve during dry operation is 1N/mm2 x m/s
Iglidur® G is designed for dry operation but P.V value is increased with continuous lubrication in oil, grease, water or other liquids.
| Pressure (N) | Rpm / (Bore Ų x  ) |
|||
| (Load) N/mm2 | (Velocity) m/s = | |||
| Bore Ų x Length (mm) | 60 |
Co-efficient of friction against steel shaft (50 HRC 1µm): Dry 0.09 - 0.22 Grease 0.09 Oil/Water 0.04
Recommended Running Shaft: Hard Steel 50 HRC 0.8-2µm Finish
Downloads
PDF Documents : Catalogue Pages | Iglidur® Bearings Technical | Full Range of Iglidur Bushings
Copyright © Ondrives Ltd 2012. All Rights Reserved. Powered By multisys Liaison™ | Login