Discounts

1+ 0%

10+ 5%

25+ 10%

50+ 15%

100+ 20%

200+ 25%

500+ 30%

1000+ 40%

2000+ 45%

Part Number	d1* E10	d2	b1 (h13)	Running Clearance with h9 Shaft and H7 Housing		Cost	Quantity	Add to Basket
				Max.	Min.
ASM0810-06	+0.040 8+0.130	10	6	0.166	0.040	£3.84
ASM0810-08	+0.040 8+0.130	10	8	0.166	0.040	£POA
ASM0810-10	+0.040 8+0.130	10	10	0.166	0.040	£4.14
ASM0811-08	+0.040 8+0.130	11	8	0.166	0.040	£4.14
ASM0811-12	+0.040 8+0.130	11	12	0.166	0.040	£4.14
ASM0812-06	+0.040 8+0.130	12	6	0.166	0.040	£4.14
ASM0812-08	+0.040 8+0.130	12	8	0.166	0.040	£4.14
ASM0812-10	+0.040 8+0.130	12	10	0.166	0.040	£4.14
ASM0812-12	+0.040 8+0.130	12	12	0.166	0.040	£4.14
ASM0814-06	+0.040 8+0.130	14	6	0.166	0.040	£4.14
ASM0814-06	+0.040 8+0.130	14	10	0.166	0.040	£4.26
ASM0912-14	+0.040 9+0.130	12	14	0.166	0.040	£4.14
ASM1014-06	+0.040 10+0.130	14	6	0.166	0.040	£3.84
ASM1014-08	+0.040 10+0.130	14	8	0.166	0.040	£3.84
ASM1014-10	+0.040 10+0.130	14	10	0.166	0.040	£4.14
ASM1014-16	+0.040 10+0.130	14	16	0.166	0.040	£4.14
ASM1016-06	+0.040 10+0.130	16	6	0.166	0.040	£4.14
ASM1016-10	+0.040 10+0.130	16	10	0.166	0.040	£4.14
ASM1016-16	+0.040 10+0.130	16	16	0.166	0.040	£4.26
ASM1214-20	+0.050 12+0.160	14	20	0.203	0.050	£3.84
ASM1216-15	+0.050 12+0.160	16	15	0.203	0.050	£4.14
ASM1216-20	+0.050 12+0.160	16	20	0.203	0.050	£4.26
ASM1218-08	+0.050 12+0.160	18	8	0.203	0.050	£4.14
ASM1218-10	+0.050 12+0.160	18	10	0.203	0.050	£4.26
ASM1218-15	+0.050 12+0.160	18	15	0.203	0.050	£4.43
ASM1218-20	+0.050 12+0.160	18	20	0.203	0.050	£4.57
ASM1416-10	+0.050 14+0.160	16	10	0.203	0.050	£3.84
ASM1416-15	+0.050 14+0.160	16	15	0.203	0.050	£3.84
ASM1416-20	+0.050 14+0.160	16	20	0.203	0.050	£4.14
ASM1420-10	+0.050 14+0.160	20	10	0.203	0.050	£4.57
ASM1420-15	+0.050 14+0.160	20	15	0.203	0.050	£4.57
ASM1420-20	+0.050 14+0.160	20	20	0.203	0.050	£4.71

* Tolerance when fitted (Dimensions following DIN 1494). Designed to fit H7 Housing and h7-h9 Shaft.

Material
Iglidur® A200 Plastic Colour white. Strong chemical resistance. FDA approved. UV resistant.

Performance
Max. Cont. Speed: (dry operation) Rotating 0.8m/s Oscillating 0.8m/s Linear 2m/s
Temperature Range: -40°C to +80°C Short period +170°C
Static pressure loads: at 20°C 18N/mm²
Max P.V valve: during dry operation is 0.1 max (N/mm² x m/s)
Iglidur® A200 is designed for dry operation but P.V value is increased with continuous lubrication in oil, grease, water or other liquids.

	Pressure (N)			Rpm / (Bore Ų x )
(Load) N/mm2			(Velocity) m/s =
	Bore Ų x Length (mm)			60

Co-efficient of friction against steel shaft (50 HRC 0.2µm) Dry 0.10 - 0.40 Grease 0.09 Oil/Water 0.04.
Recommended Running Shaft: to be Hard Steel 50 HRC 0.8-2µm Finish
Moisture Absorption: at RH50/23°C = 1.5%. Saturation in Water = 7.6%
Density: 1.14g/cm³

Downloads
PDF Documents : Catalogue Pages | Iglidur® Bearings Technical | Full Range of Iglidur Bushings